低比转速压气机轮毂轮缘型线多目标优化设计

对电动增压器用低比转速离心压气机轮毂轮缘进行优化设计。采用NUMECA/FINE Design 3D对压气机进行几何参数化,生成数据库样本,利用人工神经网络和遗传算法对轮毂轮缘型线进行优化,并进行流场分析。仿真结果表明,在设计转速为40000 r/min时,优化后设计点压比和效率分别提高6.59%和3.73%。     

Cd-substituted Mg composites with dual-equivalent permeability and permittivity for high-frequency miniaturization antennas

Spinel Mg ferrites Mg_1-xCd_xCo_0.05Fe_1.95O₄ (x=0.0, 0.2, 0.3 and 0.4) as potential agents for the miniaturization of high frequency antennas are presented. All the synthesized compositions were experimentally revealed to possess pure spinel phase. Dual-equivalent permeability and permittivity (μ'≈26, ε'≈25, x=0.3 and μ'≈29, ε'≈28, x=0.4) from 5 to 100 MHz can be achieved by introducing Cd²⁺ ions, yielding large miniaturization factors of up to 25 and 28. To figure out the effects of Cd²⁺ ions substitution on magnetic and dielectric properties, the change in microstructure is mainly investigated. Meanwhile, enhanced magnetic properties including upward saturation magnetization (Ms) (approximately 47.60 emu/g) and reduced coercivity (approximately 54.22 Oe) are obtained due to increased grain size and denser microstructure arrangements reflected from scanning electron microscopy images. With low magnitude order of magnetic and dielectric losses factors (tanδ_ε reaches 10^-4, tanδ_μ reaches 10^-2), the composites can potentially exhibit high operating efficiencies at high frequencies.     

XJM-KS型浮选机矿化器负压产生机理研究

浮选机矿化器是用于浮选矿浆预处理的重要设备，其性能的优劣直接影响到浮选机的工作效果。文章通过流体力学仿真软件FLUENT对XJM-KS型浮选机矿化器的内部流场进行数值仿真，重点研究了聚焦式喷嘴布置所带来的流场特征。模拟结果表明，高速的矿浆射流能够在混合室内产生-2.43×10Pa的负压区，从而吸入大量的空气，实现空气与矿浆的有效混合与预矿化，与传统的机械搅拌式矿浆预处理装置相比，该矿化器能够大幅度提高预矿化效果。     

小庄煤矿地应力场分布规律实测与模拟研究

地应力场主要由自重应力场和构造应力场组成,是影响井下采掘工程活动最重要和最根本的因素,掌握矿井的地应力场分布规律,对整体提高矿井的经济效益和社会效益具有重要的意义。本文在小庄煤矿区域采用套空应力解除法进行地应力场测量,并采用三维应力场反演验证测量结果,从而得出了小庄煤矿的应力分布规律,为矿井动力现象的预测预防奠定了基础。     

Magnetic field coupling microfluidic synthesis of Fe2Pt/C nanocatalysts for enhanced electrochemical catalytic oxidation of alcohol

The influence of magnetic field (MF) on electrochemical catalytic properties of carbon supported Fe₂Pt nanocatalysts is investigated. Nanocatalysts are produced through an external MF coupled microfluidic process. X-ray diffraction (XRD) measurements show that Fe₂Pt nanocrystals (NCs) with larger sizes are synthesized when an external MF of 1.4 T is applied. X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) characterizations confirm that more Pt²⁺ reduces to Pt⁰ and NCs grow larger under magnetic fields (MFs) than those without MFs. The increased coercivity indicates that more surface unpaired electrons are present and the surface spin configuration changes under MFs. NCs synthesized under MFs show better catalytic performance in alcohol electrochemical catalytic oxidation reactions compared to samples synthesized without MFs. The mass activities significantly increase by 1.10 and 1.24 times and the specific activity increases up to 1.11 and 1.26 times for methanol and ethanol oxidation, respectively, compared to those without MFs.     

Liquid-phase flash sintering 8YSZ with alkali halide sintering aids

The properties of ZrO₂: 8 mol% Y₂O₃ (8YSZ) ceramics with LiF and KCl sintering aids for liquid phase formation during electric field-assisted sintering were studied. Sintering experiments were carried out at 650 °C under 200 V cm⁻¹ AC electric field by varying current density, current application time, as well as LiF and KCl contents. Pellets sintered with KCl addition had cavities, cracks and fractures. Pellets sintered with 15 wt.% LiF, on the other hand, were homogeneous after thermal removal of LiF upon Joule heating. Low electric current densities coupled with longer application times produced homogeneous specimens. Three different stages were identified during sintering experiments: (i) LiF melting with the electric field applied at furnace temperatures lower than its melting point, (ii) shrinkage due to liquid phase formation and LiF removal, (iii) final densification due to grain growth and pore elimination. The electrical behavior and an estimate of the porosity were carried out by electrochemical impedance spectroscopy measurements.     

航天发动机叶片电解加工流场设计和试验研究

电解加工作为整体构件制造的主要技术之一,其流场设计的合理性将严重影响电解加工过程的稳定性、加工效率和质量。针对航天发动机叶片式扩压器设计了部分阻隔式反W型流场,并开展了与侧流式和反W型流场的仿真比较。仿真结果表明,该流场方式可以保证加工区电解液的高速流动,并能有效避免进/排气边漏液现象。最后,在部分阻隔式反W型流场中开展了叶片式扩压器电解加工试验,在阴极进给速度为0.5 mm/min时加工出了扩压器叶片,验证了流场设计的合理性。     

覆岩结构类型与开采覆岩损害特征分析

煤层开采打破了上覆岩层原有的平衡,必然引起岩层的移动、破断,导致应力场和裂隙场的改变,工作面出现矿压显现。上覆岩层的岩性和组合结构对工作面开采覆岩损害特征分布影响显著,一般岩性越坚硬,上覆岩层应力集中程度越高,采动裂隙越发育,矿压显现也越明显;坚硬岩层尤其是关键层对覆岩的破断运动起控制作用,覆岩破断发展到一定层位后软弱岩层往往是抑制覆岩破断进一步向上发展的关键。当工作面上覆岩层同时存在远近场关键层时,近场关键层的周期性破断引起裂隙带范围内岩层的运动和工作面周期来压;而远场关键层的周期性破断导致地表裂缝或台阶下沉,工作面压力急剧上升,有时甚至导致煤矿动压灾害,尤其是远近场关键层同步破断时动力现象更明显。通过地面钻孔使远场关键层提前破断是防止此类动力灾害的关键。     

基于永磁涡流传动的长距离带式输送机启动特性研究

针对矿用带式输送机启动过程易出现打滑、淤带和断带等问题,基于永磁涡流传动技术,将双盘式磁力耦合器作为带式输送机的驱动装置,建立双盘式磁力耦合器动态数学模型,运用AMEsim软件搭建带式输送机系统仿真模型,设置启动时间分别为60、80和100 s,采用Harrison控制曲线启动时,研究带式输送机满载启动时机头、机尾部输送带的速度特性和张力特性,张紧装置位移特性以及双盘式磁力耦合器调速气隙特性,仿真结果表明:当启动时间为60 s时,带式输送机输送带速度波动大,动张力明显,尾部输送带最大张力达到29 kN,启动过程不平稳;双盘式磁力耦合器调速时,气隙变化与带式输送机启动速度变化趋势相反,启动过程气隙从22 mm减小到4 mm;当启动时间为80 s和100 s时,带式输送机启动过程相对平稳,速度和张紧装置位移波动小,尾部输送带张力波动幅度分别为5 kN和3 kN;带式输送机启动过程存在最佳启动时间,继续延长时间,对带式输送机启动特性影响越来越小,80 s可作为合理启动时间。     

用于阀芯类零件去毛刺的磁极板优化设计与实验研究

目的 为解决阀芯类零件节流边毛刺去除不均匀和效率低下的问题，对磁极板尺寸和曲率进行规律性研究和实验验证。方法 首先，用Maxwell仿真软件对磁极板的各个参数进行规律性仿真，得出合适的磁极板尺寸;其次，为提高加工区域的磁感应强度值，设计了曲面磁极板，并对其相关参数进行仿真;最后对优化后的装置进行磁感应强度测试，并使用液体磁性磨具对45钢和阀芯棱边毛刺进行去除实验。结果 根据仿真结果发现，磁极板长度比工件大20 mm时，工件轴向磁场分布最均匀，磁极板厚度对磁场影响较小，磁极板宽度应根据加工间隙进行选择。曲面磁极板可以加强加工区域的磁感应强度值，曲率半径越小，加工区域获得的磁感应强度值越大，其中半圆形磁极板效果最佳。对装置的磁感应强度测试也表明，将工件置于磁场中后，其表面磁感应强度值最高达600 mT左右，满足加工需求。最后通过加工实验发现，在转速为500 r/min的条件下，阀芯节流边的毛刺去除效果理想，且轴向加工均匀。结论 该装置可以对阀芯这类导磁性回转类零件产生良好的加工效果。